|
If you have any questions about the RT1000 router tables e-mail Joe
joe@rt1000.com
You can make the lower half to suit your height.
Save on freight
as the main box is smaller.
Included is 10 ft of walnut trim.
The RT1000SX is an excellent choice for any woodworking shop. Cabinet, table and fence are trimmed in solid Black American
Walnut and clear White Maple. | 
The RT1000SX is exactly the same as the RT1000XL without
the lower half. The table top is 32" wide x 24" deep , hefty 1.1/2" thick for stability and flatness. 
The
cabinet is constructed using 18 mm Baltic birch plywood. This plywood is 13 layers of solid veneer ply's The shelves and
uprights are made of 3/4" industrial grade melamine. Joints are dado, rabbet, glued and brad nailed very well built |
There are 5 drawers in our router tables. 2 drawers hold 44 -- 1/4 router bits. 2 drawers hold 28--
1/2" router bits. We can modify these in case you prefer all 1/2 drawers. One drawer to store your wrenches, template guides,
bearings etc. | | 
The RT1000SX model comes with a Miter-T-Track for those miter
gauges that have a t-slot bar. Standard miter gauges will also work with this track. There are two electrical outlets in
the base cabinet that are controlled by a Safety Paddle Switch It has a removable yellow lock to
prevent unwanted start ups. Also a 8 foot power cord wired for 110-120 volts. 
The insert plate is made out of 3/8 Lexan. Very strong
and has 8 leveling set screws. One insert is included with each router table. There are 3 sizes available. (Blank), (2")
and (3.5") opening. If not specified at point of sale a 2" will be included with each order. Insert size is 9 1/4" x 11
3/4" x 3/8". The same size as most popular router lifts.
2 1/4" star knobs for locking down the fence | |
The RT1000SX has a 3.5" dust port on the left side for attaching your vacuum
system (easily adapted to 4"). It has a 2.5" port cut in the top under the fence, in case you want to use a smaller hose
(shop vac). There are 3 vented holes in the acrylic door, allowing air flow to circulate which keeps the router compartment
free of dust. The(hinged)door covering the router compartment has a magnetic catch to hold the door closed |
The fence includes an alum. t-track for attaching feather boards, stops, guards and other fences and
jigs. Each sliding fence on this split fence system can be adjusted over 1/2" for glue joint work. More importantly, it will
go back to a straight edge in seconds. For vertical panel a high fence can be easily adapted, 3 T-bolts are included. So
you can make yours as high as you want. 
The fence sliders will open from 1/2" to 5". You
can be set it up 1/2" in front of the bit, for taking multiple passes and slide back as much as 5" for routing inside front
edge. For those odd shapes or free hand work, set it completely back and wide open this unit will still collect 99% of the
saw dust. |
The bottom cabinet comes fully
assembled and packaged in a box surrounded in Styrofoam. 24" x 21" x 22" The top is shipped in a separate box. 35" x 26" x
5.5" After receiving your RT1000XL, it may takes 10 to 15 minutes to assemble the top to the lower cabinet using the supplied
hardware and mounting instructions, then your ready to go. | |   | |
|
|
Freight cost for RT1000SX
To add freight for a complete router table, please click
on the add freight button for your province.
There will be no extra charge on accessories added to the main order.
If ordering accessories only, please email us your list plus address for freight cost.
|
BC $79.00 |
Alberta $72.00 |
Saskatchewan $69.00 |
Manitoba $65.00 |
Ontario $58.00 |
Quebec $55.00 |
New Brunswick $49.00 |
Nova Scotia $35.00 |
PEI $45.00 |
Newfoundland $69.00 |
|
|
USA
Freight cost for RT1000SX Select a Zone,(which contains your State) for shipping
charge on complete table and click on (add to cart).
table test
|
